Rotary drilling rig power head maintenance measures

Rotating drill mainly in sandy soil, cohesive soil and silty soil layers etc construction, in the bored pile, diaphragm wall, foundation reinforcement etc widely used in a variety of ground foundation construction. Rotary drilling rig power head maintenance measures are respectively replacement of the rotary digging drill power head lubricating oil, inspect and replace power head spline gear oil.

Introduce below rotating drilling rig power head maintenance measures steps. I hope to give faithful car to bring some help.

1, often through the gearbox hole cover transparent glass to check the height of the gear in the lubricating oil, the oil level of guarantee from an altitude of no less than eight hole glass two-thirds of the vertical height.

2, change gear oils, power head first gear oil drain plug is easy to operate and to lower the position of the discharge of oil.

3, Remove the plug screw and Oil lever plug, Let the power head gear oil discharged into a suitable container, emissions can be appropriately in the process of turning slowly power head gear, so that the oil drain net and exhaust pollutant, but at the moment, should pay attention to safety, gear rotates the relevant personnel should be away from the scene.

4, check the plug screws and seals. Look is intact, if there is an obvious worn or damaged, it should be replaced with a new part.

5, Oil discharge is complete, mount the plug screw.

6, unscrew the power head accumulator hydraulic hose connectors, pay attention to protect the purity of the joint, through the joint hole to gear box filling lubricating oil, by sight hole of glass observe the oil level height, to more than two thirds the height of the glass, but also can’t fill it up with, if fill up will cause the power head seal leak, the hydraulic oil or water into the gear box, it may pollute the gear box.

7, after the above steps, tighten the step 5 hose connector, plug oil surface, the tightening torque reference appendix.

8, start the engine and let the power headgear running laps.

9, stop the engine, check whether the oil level height is depending on the hole above the height of glass two-thirds.

TAGS:

Rotating drill power head, Drill rig power head, Drilling rig power head maintenance measures

The difference between pneumatic and electric tapping machine

Taizhou road machinery co., LTD. The main production of various kinds of power head, tapping power head, tapping power head, pneumatic power head, drilling power head, drilling power head, drilling tapping head, servo tapping machine, tapping machine, hydraulic gear type damper, custom make all kinds of multi-axis device, porous automatic drilling machine, non-standard combination machine tools and so on.

Tapping machine is a machine tap processing of internal threads, it is the most widely used a kind of internal thread processing machine tool. According to the national machinery industry standard, tapping machine series is divided into: desktop tapping machine, semi-automatic desktop tapping machine, vertical tapping machine, horizontal tapping machine. A kind of important for some reason the classification of the most widely used is not included, namely, folding boom tapping machine.

Pluto (PURROS) introduce the difference between pneumatic and electric tapping machine, pneumatic tapping machine is through the air compressor compressed air driven motor, electric tapping machine with 220 v electric can drive. General electric tapping machine service life longer than pneumatic tapping machine. Electric tapping machine tapping fangs in strength at the same time, high efficiency, energy saving and energy saving, no noise, the torque is very stable, idle speed is the same as the actual speed. If it is a large amount of tapping and economic conditions permit, it is recommended that you choose electric tapping machine, price is relatively high. If tapping the amount is not big, can consider to choose pneumatic tapping machine. If you M2, M3, M4, M5, M6 thread teeth is more, it is recommended that you choose pneumatic tapping machine, this is money, efficiency is very high.

The road, can according to their own product features, different requirements, choose the right model, requirement of each parameter can also provide to us, we can help you customized tapping machine is most suitable for you.

TAGS: the difference between pneumatic and electric tapping machine, tapping machine manufacturers, the application of tapping machine, pneumatic tapping machine

Electric tapping machine operation and composition

Electric tapping machine is applicable to all machinery manufacturing industry, machine tool, mold (factory) machinery, plastic machinery, printing machinery, packaging machinery manufacturers, engineering machinery, automobile motorcycle parts, aviation engines, rolling stock, tobacco machinery and general machinery and other industries.

Electric tapping machine is also known as: tapping machine, tapping machine, tapping machine, universal electric tapping machine, tapping machine, universal electric tapping machine, electric tapping machine, blind hole tapping machine, tapping machine, tapping machine, electric tapping machine, universal tapping machine, universal electric tapping machine, universal electric tapping machine universal electric tapping machine. Portable electric tapping machine, flexible, efficient, and possesses the advantages of other similar equipment cannot be replaced.

Pluto (PURROS) under the company to introduce the electric tapping machine operation and constituent parts:

A, electric tapping machine operation:

After turning on the power supply, open the power supply controller, tapping speed have been set, press forward, servo motor output torque and rotational speed voltage signal can be converted to tapping operations, tapping the bottom hold the reverse button back. Work high precision, check rules can be detected.

B, electric tapping machine consists of the following sections:

1, servo motor: to convert voltage signal into torque and rotational speed to drive control object.

2, controller, power control and torque overload protection.

3, display, advance and retreat silk speed control regulation.

4, tap torque protection chuck: adjust the chuck torque size, tap tapping to the bottom of the blind hole over the distance, slip protection.

5, support: can adjust elevator, within a radius of action of any position tapping.

TAGS: The operation of the electric tapping machine, Electric tapping machine, Electric tapping machine advantages, Scope of electric tapping machine

The characteristics of the electric tapping machine

Tapping machine is a machine shell, end face, such as nuts, flange with different specifications of the hole or blind hole of the inner side of the hole of the parts work out internal threads, screws or tooth buckle mechanical processing equipment.

Electric tapping machine is also known as: tapping machine, tapping machine, electric tapping machine, universal electric tapping machine, tapping machine, universal electric tapping machine, and so on. Electric tapping machine is applicable to all machinery manufacturing industry, machine tool, mold (factory) machinery, plastic machinery, printing machinery, packaging machinery manufacturers, engineering machinery, automobile motorcycle parts, aviation engines, rolling stock, tobacco machinery and general machinery and other industries.

Pluto (PURROS) production and sales of tapping machine are: servo tapping head, guide tooth stem tapping machine, tapping machine gear type. The following is the characteristic of PURROS electric tapping machine:

1, the top speed of 3370 RPM high speed machining.

2, maximum tapping capacity: aluminum alloy: M14, steel: M12

3, using high-performance servo motor. Numerical control system, ensure the accuracy of the thread at 6 h high margin.

4, can be used with multi-axis device, the effect is better.

5, can be arbitrarily set the second origin, set to ride fast, compared with the lead screw or into full gear type tapping machine stroke work, increase efficiency of the machining.

Tapping machine, drilling, tapping operations can also be equipped with multi-axis device, improve efficiency. Is the product of high precision machining, production products can match for automatic operation, such as: motorcycle parts, auto parts and other parts of high requirements and production.

TAGS: The characteristics of the electric tapping machine, Electric tapping machine manufacturers, Electric tapping machine applicable scope, The definition of electric tapping machine

Principle of tapping machine is introduced

Tapping machine is a machine shell, end face, such as nuts, flange with different specifications of the hole or blind hole of the parts for the inner side of the internal thread, screw or call button of mechanical processing equipment. Tapping machine is also called the tapping machine, thread tapping machine, tapping machine, automatic tapping machine, etc.

Pneumatic tapping machine is applicable to all machinery manufacturing industry, now mainland customers covers tools, mould (factory) machinery, plastic machinery, printing machinery, packaging machinery manufacturers, engineering machinery, automobile motorcycle parts, aviation engines, rolling stock, tobacco machinery and general machinery and other industries.

Pneumatic tapping machine is portable, flexible, efficient, and possesses the advantages of other similar equipment cannot be replaced. Repeat positioning rapid fast, scope of work, safe in operation and ordinary pump 5-8 kg, new type of pneumatic tapping machine to avoid the limitations of the lathe, drilling machine or manual tapping time and manpower, it is not easy rotten teeth, tap not easily broken, etc.

Pneumatic tapping machine driven by compressed air, safe fast and efficient; The mean pressure and volume (0.3 0.8 mpa), large torque output; To all kinds of steel, iron, copper, aluminum, plastic and other materials tapping; Cylinder with overload protection device, silk attack damage is less, the teeth of high precision; With simple operation light, no experience and strength; Machining cost is used CNC machining center, milling machine tapping machine or hand tapping is low; The heavier work content does not require positioning device or mobile, heavy work area (100-2000 – mm radius range); Positioning rapid fast and high cutting speed, increase production; Through hole or blind hole, silk attack are not breaking, vertical, Angle of the (universal) are tapping; Processing range: (M3 – m2-m24). The service life of the products, guarantee.

TAGS: Tapping machine advantage, Tapping machine principle, Tapping machine applicability, Tapping machine features

Manufacturer of spot supply hydraulic power head

All-hydraulic power head drill, railway and highway bridge, ventilation shaft of coal mine, port terminals, and high-rise buildings and other large infrastructure construction drilling the ideal construction equipment, can be in diameter from 1.5 to 1.5 m, the rock uniaxial compressive strength of sigma c or less 200 mpa to choose aperture in the bedrock of the drilling, drilling depth of up to 130 m, the hole diameter in the layer of 6.0 m.

Full hydraulic drilling rig is driven by power head drill pipe, drill pipe drive drilling rotary drilling, USES the air reverse circulation mode of discharge, the power transfer for: electromotor→hydraulic pump→hydraulic motor→power head.

Machinery manufacturing industry developed mainly gathered in the coastal region of zhejiang province.Taizhou purros machinery co., LTD. Is located in the manufacturing industry developed new city of taizhou in zhejiang province.The purros production drilling power head, drilling power head, hydraulic power head, which can realize high ratio of performance and high precision automatic feed power head.

Manufacturers selling power head

Power head also calls the dynamic cutter holder, is installed on the power tool turret, is driven by servo motor. This kind of cutter holder normally used in car milling compound machine, there are a few can be used in the driving force of knife tower on the machining center.

Taizhou purros machinery co., LTD. The main production and sales of various power head, tapping head, tapping head, pneumatic power head, drilling power head, drilling power head, drilling tapping head, servo tapping machine, tapping machine, hydraulic gear type damper, custom-made all kinds of multi-axis machine, automatic drilling machine, non-standard porous combination machine tools, etc., and external to undertake OEM ODM processing, incoming sample to map processing business. Company set up domestic and international trade, the products sell well and are exported to Europe and the United States, South Korea, Japan, Middle East, Africa and other countries or regions, renowned at home and abroad.

Under the purros, to introduce the company’s production of PR3P – 6049 model the various parameters of power head:

1, model: PR3P – 6049

2, brand: PURROS

3, no-load speed: 4900 r/M

4, drilling diameter: aluminum: Φ 5.5 MM/cast iron: Φ: 2.2 MM/steel Φ 2.2 MM

5, the main shaft trip: 80-120 – mm

6, cutting feed stroke: 0-60 mm

7, motor power: 0.55 KW

8, feed thrust: 1200 n

9, gas consumption: 3-6 l

PURROS drilling, drilling power head type can be divided into: PR3P type, type PR4P, PR5P type, PR6P type, etc., you can also according to their own product features, different requirements, choose the appropriate models, can also provide various parameters requirements to us, we help you order is most suited to your head.

Turning knife with dynamic characteristics

Power head also calls the dynamic cutter holder, is installed on the power tool turret, is driven by servo motor.This kind of cutter holder normally used in car milling compound machine, there are a few can be used in the driving force of knife tower on the machining center.

Turning power head through the transformation of the turning power head turning processing center in a clamping can finish turning function not only, also can finish milling function, thus makes the turning processing center and turning to expand the application scope of machine tool. Because it is a clamping to complete a variety of functions, such as turning, drilling, reaming, tapping, milling plane, slotting, incision, etc, so the work piece machining precision and high quality, but also improves the machining efficiency. Turning power head must be installed in the power output of the machine.

Taizhou road machinery co., LTD. Producing all kinds of power head of turning power head, in addition to standard products, can also according to customer request special supply, compared with foreign products, the product has excellent cost performance, performance is comparable to similar foreign products, and the price is far lower than imported products, is the ideal of machine tool users and machine tool manufacturers supporting tools, can completely replace the expensive imported products.

TAGS: Turning power head, Turning power head tool apron, Turning head characteristics, Turning power head manufacturer, Turning power head suppliers

Gear type tapping machines new technical specifications

Tapping machine is a machine shell, end face, such as nuts, flange with different specifications of the hole or blind hole part of inner side work out internal threads, thread or tooth buckle mechanical processing equipment.

Tapping machine is suitable for automobile or motorcycle body, frame, chassis, connecting rod, engine, cylinder, and various mechanical parts, machine tools, metal products, metal pipe, gear, pump body, valve, fasteners and other parts processing.

Taizhou purros machinery located in Zhejiang province machinery more manufacturing industry developed, the main production and sales of various tapping machine, the following to introduce the main gear type tapping machine utility model under instructions:

1, with a variety of hanging wheel to achieve the required thread pitch. Compared the technology on the market at present the guide screw tapping machine mechanical wear smaller, more durable, higher precision and practical is wider in scope than the drill attack amphibious models on the market, the precision of the thread is more accurate, more suitable for processing soft materials such as aluminum, plastic, sheet.

2, in the pulley block and mechanical clutch each equipped with a torque device to adjust the size of the size of the torque, in order to prevent in the machining process because of the excessive torsion of tap broken or tap slip torque is too small and can’t be processed.

3, can cooperate with multi-axis device, porous tapping at the same time, improve production efficiency and save the processing costs.

TAGS: tapping machine definition, tapping machine scope of application, tapping machine manufacturers, tapping machine suppliers, gear type tapping machine technical specification

Guide tooth type tapping head

Taizhou purros machinery co., LTD. The main production and sales of various tapping machine, servo tapping head, guide tooth stem tapping machine, tapping machine gear type. The purros to introduce the lower guide tooth type tapping head of product features:

1, high speed and precision, tapping out tooth by tooth gauge test. With special motor can run for high speed continuous loop can be durable, which can realize automation, tooth pitch type automatic tapping machine is one person can operate multiple devices at the same time, can save labor costs significantly.

2, automatic tapping machine working principle: forward – reversal – forward – reversal…Continuous loop and forward – reversal – stop one-directional button switches to a certain operation, also can install foot switch, for selective operation, continuous, one-way, circulation can be automatically. The operator’s hands can leave machine, automatic work, beginners can be operating smoothly.

3, high-precision tapping stroke; easy adjustment, automatic reverse device can free adjustment tapping stroke, shallow holes and have low holes machined part also can be easy to adjust, double safety device can prevent damage of the tap, and fluctuation of spindle, cutting AD hoc double safety clutch, spindle can automatically stop, reversed return will not damage the cutting tool.

4, tooth gear with axis and spindle, according to the tooth pitch propulsion fully compatible with the vertical stability, high precision, precision special, tap tooth forward and backward without output can function properly. At the same time depends on the fine processing items, will not result in different degree thread, for thin plate and light metals, synthetic resin and other soft goods also can attack the perfect thread. At the same time can also configure multi-axis device for multi-axis synchronous processing, the production efficiency is greatly increased.

Taizhou belongs to the coastal areas of Zhejiang area, the geographical position is superior, the purros machinery co., LTD. Producing all kinds of mechanical products, the purros, the production of tapping head is simple a variable speed drive mechanism, has taken many forms, is a kind of can realize boring, milling, drilling, and other functions of the equipment.

TAGS: Guide tooth type tapping, Guide tooth type tapping head characteristics, Guide tooth type tapping head supplier, Guide tooth type tapping head manufacturer